Comparison of 2 methods to establish mandibular three-dimensional finite element model

Liu Minyi; Zhang Jing

您当前的位置：

首页 >

文章列表页 >

Comparison of 2 methods to establish mandibular three-dimensional finite element model

更新时间：2025-01-15

- Comparison of 2 methods to establish mandibular three-dimensional finite element model
- Journal of Army Medical University Vol. 35, Issue 6, Pages: 532-535(2013)
- 作者机构：
  
  重庆医科大学附属口腔医院，口腔疾病与生物医学重庆市重点实验室：沙南街门诊部，整形美容科
- 作者简介：
- 基金信息：
- DOI：
  CLC： R312;R319;R323.1
- Published：2013，
  
  Published Online：30 March 2013，
- 稿件说明：
移动端阅览
LIU MINYI, ZHANG JING. Comparison of 2 methods to establish mandibular three-dimensional finite element model. [J]. Journal of army medical university, 2013, 35(6): 532-535.
DOI：

LIU MINYI, ZHANG JING. Comparison of 2 methods to establish mandibular three-dimensional finite element model. [J]. Journal of army medical university, 2013, 35(6): 532-535. DOI：

摘要

目的探讨直接建模和间接建模方法在下颌骨三维有限元建模中的应用。方法使用相同的序列CT图像，应用直接建模和间接建模方法分别建建立下颌骨的三维有限元模型，采用相同边界条件和载荷进行计算，对计算结果进行分析和比较。结果两模型在峰值载荷时的von Mises应力分布情况一致，直接法模型应力集中区域von Mises应力为87～195 MPa，间接法模型为101～153 MPa；应力集中节点时间-应力曲线近似；两模型下颌骨体部、磨牙后区、髁突颈对应节点应力值差异无统计学意义(

>0.05)。结论两种建模方法各有优势，所建模型都能从整体上反映下颌骨的生物力学特性。

Abstract

Objective To apply direct modeling and indirect modeling in the establishment of a three-dimensional finite element model of mandible and temporomandibular joint with high biomechanical similarity. Methods The magnitude and distribution of Von Mises stress in mandibular three-dimensional finite element model established by the direct modeling and indirect modeling was compared and analyzed. Same boundary conditions were adopted. The same level of anterior-posterior impact load at the mental symphysis was analyzed. The results were analyzed and compared. Results In the peak of load

the von Mises stress distributions of these 2 models were similar. The value of von Mises stress in stress concentration area of direct m

odeling ranged from 87 to 195 MPa

and from 101 to 153 MPa in Model B. Paired student’s t test was used to analyze the value of each node on 3 corresponding areas of each model

and the results showed that the differences between the 2 modeling had no significant difference (

>0.05). Conclusion These 2 three-dimensional finite element models of mandible established by direct and indirect modeling are of highly biomechanical similarity.

关键词

下颌骨三维有限元分析建模

Keywords

mandiblethree-dimensional finite element analysismodeling

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of functional mandible shift on mandible morphology of pubertal rats

Expression of insulin-like growth factor-1 in bony class Ⅲ malocclusion

Related Author

WANG Chao

BAI Liyun

JI Ping

YANG Zhiqiang

Tan Yinghui

Miao Yingyun

Zhang Gang

Cheng Yubin

Related Institution

Department of Oral and Maxillofacial Surgery, Chongqing Key Laboratory of Oral Diseases and Biomedical Science, Chongqing Municipal Key Laboratory of Oral Biomedical Engineering of Higher Education, Stomatological Hospital of Chongqing Medical University

Department of Stomatology, Xinqiao Hospital, Third Military Medical University

Department of Stomatology, Institute of Surgery Research, Daping Hospital, Chongqing

Laboratory of Transmission, Chongqing University

Department of Orthodontics, Affiliated Hospital of Stomatology, Chongqing Medical University

⁰